OES SR 105 goes into CNC production

Dont think it will work... all those jagged edges are going to cut your feet. Although it might work on the back half, acting like little winglets!

The 2010 SR105 Slalom board is a 236cm Length X 68 cm width x 105 L,
Full Carbon, CNC Milled core with a full veed bottom with a slight double concave in the nose to mid section to aid turning and smooth the ride at full speed.

Nice looking board there Pete. I like the widepoint forward of centre and the snub nose.
What is the sweet spot and range of the board like? Would 7-7.8/36-40 be around the mark?
Are they available in your classic silver or custom graphics and what would the lead time be?
Cheers, Tim.

Nice looking board there Pete. I like the widepoint forward of centre and the snub nose.
What is the sweet spot and range of the board like? Would 7-7.8/36-40 be around the mark?
Are they available in your classic silver or custom graphics and what would the lead time be?
Cheers, Tim.

Hi Tim
Thanks for your comments about the new 2010 SR105. After spending alot of time on our wave shapes over the last few years , it was time to reinvest some more time and resources into our slalom and speed shapes.I have been building these boards right from the start back in 1988 with the first 10 boards, the classic 9' x 22'' slalom and 8'10 x 18''speed boards
So I have based the new designs on we have learn from 21 years of boards design and building, with wide point forward of centre to add volume and surface area were you need it, to counter the reduced length . Reducing surface area as much as possible after this point towards the tail with it parallel rail planshape for greater control and speed both in gybing and topend.
The bottom shape is as clean as possible with NO cutouts ,wingers or double upwind rails, just a veed bottom that has it max vee and double concave depth just farward of centre .There is also a very small amount of flat panel vee out the tail to stop sideways slip at speed. It has a 700mm straight in the tail rocker with a 17 cm nose rocker for better nose clearace in chop so the board can be push harder in real world choppier condition.The rails are profiled fairly low at 25mm apex again for greater control in high speed turning without risk of rails planing out of the water in high speed gybes.
We have always used a 3 mm deck concave to stop the lift from air flowing across the deck and to also slighty lowers the mast base to lower the centre of effort on the board from the sail .It also stiffen the carbon deck with the concave as it acts like parabolic stringers that follow the planshape 122mm from the rail.
Construction is full Carbon/ Corecell both top and bottom lamination with no cheap water sucking wood veener . All cores are CNC milled and the boards are vacuum baged 5 times into our rocker moulds at each stage of construction to ensure that there is no flex or spring in that production stage . All resins and carbon cloth is both weighed and templets to ensure no extra weight is added to the construction. All carbon cloth is preplug off the boards on our lamination tables then tranfered to the board and vacuum down on to the Corecell with out blog, which add weigth and reduces the chemical bond between the lamintaion and the Corecell hard foam .
The boards are all painted with the best with 2k PPG paints with extra layer sprayed on the rails to better protect them.
No problem with the sliver colour basespray or any other colour you wish.
7-7.8/36-40 would be the sweet range of sail size and fins , we have also used 6.5 and 34cm.
Lend time will be 3 to 5 weeks with a week extra for shipping as there is a lot of work that is needed to going into each of them, to make sure that they are 100% right.
Just sent our first shippment of 2010 to Holland with then next batch to Sweden.
If you have any more questions or info best to PM me
cheers
Pete.
PS Hopefully will get some video and photos up over the next day or so of a SR105 being CNC milled.

Prepairing the blank , to find the end points of the board ,so it can be placed on the cutting bed .

Deck being milled

Bottom being milled

Hey Pete, How long does the machine take to mill a board top and bottom?

The milling only takes about 10 mins each side , it the pre work, that takes the time , making sure the the blank is in the right place on the cutting bed to mill.
The clock in the first photo is 4.15pm at the start , with the bottom being milled it show 5.40pm, so to answer you question it took 90 mins ,about the same time if I had hand shaped it!!
I have some short video of the cutter speed but am still to working out how to post it in video format. OLD SCHOOL !!

I thought that might be the case. Do you put it back on the machine once you've bagged the PVC on or do you finish it by hand?

Select to expand quote

hoop said...

I thought that might be the case. Do you put it back on the machine once you've bagged the PVC on or do you finish it by hand?

i was wondering the same thing, if the board is totally shaped how do you keep the blank in shape when vac/bagging

All cores are CNC milled and the boards are vacuum baged 5 times into our rocker moulds at each stage of construction to ensure that there is no flex or spring in that production stage .

Just got this in from my dealer in Holland of the first two boards we sent him an XWave 85 and a SR105 Slalom.






Hi All,

i have yesterday received 2 boards, the slalom 105 and the Xwave 85!

As all ready told pete, i'm very impressed, the looks, the weight etc.

When customers see this they want to have them!







Pete,

had a go on both boards today! wave is brilliant:-)

slalom is fasssssssssssssssssssssssst ,good control and very easy jibing


i used a C3 venom 40 cm and a KA slalom 37 with a KA koncept 7.5