Gday everyone,

One of the guys today had his GPS set to Data Logger...Log Switch... OFF. This meant there was no file on his card. I did "save to card" but just gave a couple of small files.

Is there any way to retrieve the info from the session apart from the tripmeter log? I am trying to do a 1 hr calculation.

Needless to say I fixed the setting to "ON" but would be good to get any data out.

Here is the SG_TRP.SPD extract.

Thanks
James


*** HISTORY SPEED LIST ***
USER:xxxxx,SNO:133200912
---MAX SPEEDS---
[ 1] 31.56 KTS
[ 2] 27.52 KTS
[ 3] 27.13 KTS
[ 4] 26.12 KTS
[ 5] 25.48 KTS
[ 6] 25.19 KTS
[ 7] 25.03 KTS
[ 8] 24.58 KTS
[ 9] 24.51 KTS
[10] 24.20 KTS
[11] 23.63 KTS
[12] 23.55 KTS
[13] 23.40 KTS
[14] 23.38 KTS

---MAX AVG SPEEDS---
[ 1] 30.80-10S KTS
[ 2] 27.13-10S KTS
[ 3] 26.68-10S KTS
[ 4] 25.46-10S KTS
[ 5] 25.01-10S KTS
[ 6] 24.72-10S KTS
[ 7] 24.29-10S KTS
[ 8] 23.94-10S KTS
[ 9] 23.92-10S KTS
[10] 23.81-10S KTS

---TRIP METER---
TRIP ODOMETER??=22.12 NM
TRIP TIME??=5:26:18
STOP WATCH??=5:26:18.00
TRIP AVG SPEED??=4.06 KTS
TRIP MAX SPEED??=31.56 KTS
THRESHOLD SPEED??=0 KTS

Sorry if neither the card or the data logger was recording, I think that's it.
Which begs the question, why wasn't the card recording?
Was that also off? If so you'd better fix that as well, think it should be either "on" or "on fix" and recording "1sec sbin"

Could.he not take all the small files and.combine them with gpsresults?

Thanks for the ideas guys. the small files were from after I turned on LOG SWITCH.

Decrepit, are there two places where you have to turn LOG SWITCH = ON? I just changed it in Data Logger menu.

Cheers
James

Select to expand quote

jamesf said..

Thanks for the ideas guys. the small files were from after I turned on LOG SWITCH.

Decrepit, are there two places where you have to turn LOG SWITCH = ON? I just changed it in Data Logger menu.

Cheers
James

Sure is, data logger is just the internal memory, it's much better if the device records directly to the SD card.

After "Data logger" in the scroll menu, is "Memory Card" Select that, and you have the following menu.

Log Switch, should be set to "on" or "on-fix" (there's different opinions on this one, but on means the card records all the time, on-fix means it only records when it has a satellite "fix")

Min Speed, set to "off" or a very low value, probably no more than 5kts. Again different opinions on this one, Off means always recording, a speed value set, is the speed above which it starts recording

NMEA items, set to "SBN 1sec"

File Size set to "card size". This is often set to a specific value, which means once that size is reached a new file is started, then you have to stuff around joining files up.

With the above set up you should see a .sbn file on the card after each session, you shouldn't need to save the data logger to the card.
The main advantage of doing it this way is when you have a long session, I think the max the internal data logger can hold is about 7hrs, whereas the memory card will keep going until the battery runs out.

if you are going for alphas make sure the min speed is set to zero or your turns can get nulled.

Select to expand quote

Roar said..

if you are going for alphas make sure the min speed is set to zero or your turns can get nulled.

That's a good point, especially if you're not doing full planning gybes yet.