FinsUp - spewing man!!!
Geez, where do you start?
I'd definitely reach out to the manufacturer and see if there's a way to fix that's effective and low cost.
Is this common with this brand?
I'd be keen to understand how moisture gets in underneath that paint?
I'd be looking for advice from the manufacturer- you'd reckon a new full carbon board would last a bit longer than a few months eh?

Arrrgh, thats a pain isnt it!

I had a small amount of it on mine last year, since then a good shammy off after a surf and when I can leave it out of the bag or leave bag unzipped.

Hard to stop all moisture but it seems to have helped.

yeah its not a huge issue. Got a reply can just sand and touch up if need be. Otherwise no probs with integrity.

- contact the manufacturer. Different types of paint / varnishes exist, he may have relevant advice
- let it dry, the bubbles will most likely disappear
- never store in a bag. Use a bag for travel only, (with the zipper open as much as possible), and store it out of a bag.

yep bag's for travel only from now on.
And yes the good thing is, it takes the wince out of any nick or bumps from now on too.
Just surf it!!!
Cheers

justaddwater said..
Totally agree ! bags are for travel protection ,other than that they are more trouble than they are worth .IMO.About the paint finish go rat look,I personally love the distressed rub through look

Yep FinsUp - fully agree with JustAddWater on this one.
Sick opportunity to go all out Rat-vibe.
Embrace your inner Derek Hynd - keep it Core and carve your own lines.

The same problem happened on my Fanatic Allwave Carbon, the blue one like this. Let it dry on open air the bubbles probably disappear like my Allwave. On Fanatic there was also a little red label with the warning about the moisture.

check, check.... check,
and,
check.

Finsup. Thanks for the warning. Sometimes I forget to keep my board bags open to air them out. So today I checked most of my SUPs. And guess what? One of them showed some minor osmosis. It was my Coreban that I use quite often for foilboarding. I converted it to take a foil just over 2 years ago.
I mainly store it on its rail in the garage.
So I found the osmosis mid length on the rail that touches the floor. So I'm guessing the moisture from the deck bad may flow downwards to that spot and will keep it moist for longer than othe parts of the board.
I always rinse my boards with fresh water & towel dry after a surf before putting them in the bag. But towel drying doesn't ensure complete dryness. Especially deckpads that soak in water.
I'm guessing it's the paint more so than epoxy. My Sunova boards have no osmosis at all. They aren't painted. One of my Sunova's is around 6 or 7 years years old & has always been bagged. And has been used heaps!
I'm guessing some paints are more susceptible to osmosis than others.
So many different grades of paint on the market & virtually impossible to know what type of paint is sprayed over a board when new.

finsup said..
Crapola that's a bugger. Looks like you got it early though.
doesn't look too bad.
My photos are quite close up and do make it look worse than it actually is. Its been dry now for a while and I think (maybe telling myself!) that its flattening out a bit.
and yes, no way I'm replicating the finish on the carbon it's a mega thin almost transparent coat. Just gonna have to stay how it is and serve as a lesson learnt I reckon.

Yeah. Give it time & wait & see. Maybe in the future as your board gets older you may want to give it a sand & respray if it's needed at all.
The board I've shown has quite a few battle scars including the paddle blade slicing through the deck a few times. So this osmosis is nothing. The bottom of the board is still like new.
And I've actually painted an extra coat of epoxy over the right side rail for extra protection before sticking rail saver over that as well. I'm more brutal on my foil board than my SUPs.

colas said..

Seajuice said..
So many different grades of paint on the market & virtually impossible to know what type of paint is sprayed over a board when new.

Osmosis is water seeping through the paint, and then being stopped by the underlying epoxy. It can then accumulate and create bubbles. So it is only an issue on painted boards.

There are different kind of paints (glycerophtalic, acrylic, epoxy....). You should contact the manufacturer to know which one was used.

Thanks for confirming Colas. Something to take into account when buying new.